Classé Sigma AMP2 Details
Classé Audio Sigma AMP2 Two-Channel Amplifier
- 2-Channel Amplifier
- Switching technologies for both power supply and amplification stages
- New class D amplifier topology
–Travis Allanson, Secrets of Home Theater and High Fidelity
The Classé Sigma series AMP2 is a 200-watts-per-channel stereo amplifier utilizing switching technologies for both power supply and amplification stages. A Classé-designed switch mode power supply with Power Factor Correction makes over 1,000W of clean and stable power available while being both compact and efficient. A new class D amplifier topology provides wide dynamic range, smooth and extended frequency response and rich harmonic detail to yield stunning sonic performance. The efficiency of class D adds efficiency, low heat dissipation and relatively small size to the list of the AMP2’s attributes.
Sigma series amplifiers are designed to pack tremendous power, performance and value into relatively small and energy efficient chassis. The Sigma series AMP2 is derived directly from the acclaimed Delta series CA-D200, sharing both power supply and amplifier circuitry. In the same way that the Classé CT series models use the same circuitry as the equivalent Delta series but in a different chassis, the AMP2 is actually the 200W/Ch CA-D200 in a Sigma series chassis. The AMP5 also shares these same power supply and amplifier topologies, but with the necessary changes implemented to accommodate its five-channel configuration.
The basis of the design is switching technologies, used in both the power supply and audio stages. A Classé designed Switch Mode Power Supply (SMPS) and Power Factor Correction (PFC) circuit, each operating at over 90% efficiency, provides a crystal clear reservoir of over 1kW of power. The low frequency dynamics, extension and control of these amplifiers and their ability to effortlessly drive difficult speaker loads can be credited in large part to the powerful and sophisticated power supply they employ. This combination of SMPS with PFC allows the Sigma series amplifiers to draw current from the wall throughout the voltage cycle, avoiding the sharp spikes of current drawn by conventional power supplies. Such sharp and short current demands cause high-frequency harmonics on the AC mains. By creating no such disturbance, the Sigma series amplifiers deliver their prodigious power while remaining effectively silent as far as the AC shared with preamp/processor and source components.
AMP2 and AMP5 audio circuits use a true digital architecture, taking advantage of DSP to solve an issue called dead-band-time, the greatest source of distortion in otherwise well-designed class D amplifiers. Dead-band-time, somewhat analogous to switching distortion in a class A/B amplifier, is the time when the plus and minus halves of the amplifier are both off; it should be as close to zero as possible and in this design it is less than three nanoseconds. With inherently low distortion, the Sigma series amplifiers use only a small level of overall negative feedback, helping to achieve low intermodulation distortion. Proprietary driver stage FETs ensure quick and precise switching of the output stage, contributing to the amplifiers’ vanishingly low dead-band-time and maximizing their efficiency. The critical output stage filters are then used to filter only the 384 kHz switching frequency, leaving the amplifier with a neutral, extended and open upper midrange and high-frequency performance.
The Sigma AMP2 and AMP5 owe their outstanding performance and value to the unique engineering and manufacturing capabilities of Classé in Montréal and the B&W Group globally. No other high-end audio designers have access to the resources necessary to deliver such amplifiers at such competitive prices. The AMP2 and AMP5 have been conceived and built as examples of quality and value without peer. They will stand as benchmarks in the advancement of class D amplifier technology.
|Name||Classé Sigma AMP2|
|Sub Title||2-Channel Amplifier|
|Shipping Offer||AUTHORIZED DEALER - FULL WARRANTY - FREE SHIPPING|
- Frequency response: 10Hz – 20kHz, -1dB into 4Ω
- Output power: 200W rms into 8Ω 400W rms into 4Ω
- Harmonic Distortion: <0.018% @ 1kHz Balanced Input
- Peak Output Voltage:
- 116V peak to peak, 41V RMS no load
- 116V peak to peak, 41V RMS into 8Ω
- Input Impedance: 100kΩ Balanced / 50kΩ SE
- Voltage gain: 29 dB
- Input level at clipping: 1.4Vrms Balanced/SE
- Intermodulation Distortion: >80 dB below fundamental into 8Ω Balanced
- Signal to Noise Ratio: -100 dB at peak output into 8Ω (AES17)
- Rated power consumption: 177W @ 1/8th power into 4Ω
- Mains voltage: 100V - 240V, 50/60Hz
- Overall Dimensions:
- Width: 17.00" (433mm)
- Depth (excluding connectors): 14.57" (370mm)
- Height: 3.75" (95mm)
- Net weight: 22.0 lb (9.97 kg)
- Shipping weight: 28.0 lb (12.70 kg)